.HP Deskjet 2510 All-in-One series.Contents 1 How Do I?.3 2 Get to know the HP Deskjet 2510 Printer parts.5 Control panel features.2.1 How Do I? Learn how to use your HP Deskjet 2510. Printer parts Copy documents or photos Load media Replace the cartridges Clear a paper jam How Do I? 3.Chapter 1 4 How Do I?.2 Get to know the HP Deskjet 2510. Printer parts Control panel features Status lights Printer parts 1 Input tray 2 Input tray guard 3 Paper-width guide for the input tray 4 Control panel 5 Cartridge door 6 Output tray 7 Output tray extender (also referred to as the tray extender) 8 Cartridges Get to know the HP Deskjet 2510 5.Chapter 2 Control panel features 1 Power: Turns the product on or off.

When the product is off, a minimal amount of power is still used. To completely remove power, turn off the product, then unplug the power cord. A blinking power light indicates there is an error on the printer. See Status lights for more information. 2 Scan: Initiates a front panel scan job after connection to computer has been established.

3 Cancel: Stops the current operation.(continued) Behavior Cause and solution Power light, ink levels, and attention light are blinking. Ink access door is open. See Prepare the trays. Both ink level icons are blinking. Both cartridges are missing, or do not have the tape removed, or may be defective. Install cartridges, or remove the pink tape from the cartridges, or replace the defective cartridges. See Replace the cartridges for more information.

One ink level icon is blinking.Chapter 2 (continued) Behavior Cause and solution Power light, letter 'E', media icon, ink level icons, ink drop icon, and attention light are blinking. Printer is in an error state. Reset printer. Turn printer off. Unplug power cord. Wait a minute, plug power cord back in.

Turn on printer. If problem persists, contact HP. One ink level icon and ink drop icon are blinking, and the attention light is on.

Blinking ink level icon indicates that corresponding cartridge has a problem.3 Print Choose a print job to continue. Print documents Print photos Print envelopes Print documents To print from a software application 1.

Make sure the output tray is open. Make sure you have paper loaded in the input tray. See Load media for more information. From your software application, click the Print button.

Make sure the product is the selected printer. Click the button that opens the Properties dialog box.Chapter 3 NOTE: You can print your document on both sides of the paper, instead of just one side. Click on the Advanced button on the Paper/Quality or Layout tab. From the Pages to Print drop-down menu select Print Even Pages Only. Click OK to print.

After the even numbered pages of the document have been printed, remove the document from the output tray. Reload the paper in the input tray with the blank side up, and top of page down.NOTE: For specific details on how to format text for printing on envelopes, consult the help files in your word processing software. For best results, consider using a label for the return address on envelopes. To print envelopes 1.

Make sure the output tray is open. Slide the paper guide all the way to the left. Place the envelopes in the right side of the tray. The side to be printed on should face up. The flap should be on the left side.

Push the envelopes into the printer until they stop. 5.Chapter 3 Printer settings tips.

On the Paper/Quality tab of the print driver, select the appropriate paper type and quality from the Media drop down menu. On the Advanced tab, and select the appropriate paper size from the Paper Size drop-down menu. Click the HP Deskjet 2510 series desktop icon to open the Printer Software.6.

In the Media drop-down list, click Photo Paper, Best Quality. NOTE: Photo Paper, Best Quality must be selected from the Media drop-down list on the Paper/ Quality tab to enable printing in maximum DPI. Click the Advanced button. In the Printer Features area, select Yes from the Print in Max DPI drop-down list. Select Paper Size from Paper/Output drop-down menu. Click OK to close the advanced options. Confirm Orientation on Layout tab, then click OK to print.Chapter 3 14 Print.4 Paper basics You can load many different types and sizes of paper in the HP Deskjet 2510, including letter or A4 paper, photo paper, transparencies, and envelopes.

This section contains the following topics:. Recommended papers for printing Load media Recommended papers for printing If you want the best print quality, HP recommends using HP papers that are specifically designed for the type of project you are printing. Depending on your country/region, some of these papers might not be available.Chapter 4 HP Printing Paper. HP Printing Paper is a high-quality multifunction paper. It produces documents that look and feel more substantial than documents printed on standard multipurpose or copy paper.

It features ColorLok Technology for less smearing, bolder blacks, and vivid colors. It is acid-free for longer lasting documents. HP Office Paper. HP Office Paper is a high-quality multifunction paper.

It is suitable for copies, drafts, memos, and other everyday documents.c. Slide paper-width guide to the left Slide paper-width guide to the left. Insert stack of paper into input tray with short edge forward and print side up. Slide stack of paper down until it stops.

Christina tosi milk bar recipes

Slide paper-width guide to the right until it stops at edge of paper. Load small-size paper a. Raise the input tray Raise the input tray.Chapter 4 b. Lower the output tray Lower the output tray and pull out the tray extender. Slide paper-width guide to the left. Slide paper-width guide to the left.

Insert stack of photo paper with short edge down and print side up. Slide stack of paper forward until it stops.

NOTE: If the photo paper you are using has perforated tabs, load photo paper so that tabs are on top. Slide paper-width guide to the right until it stops at edge of paper.Load envelopes a. Raise the input tray Raise the input tray. Lower the output tray Lower the output tray and pull out the tray extender. Slide paper-width guide to the left.

Slide paper-width guide to the left. Remove all paper from the main input tray. Load envelopes. Insert one or more envelopes into far-right side of the input tray. The side to be printed on should face up. The flap should be on the left side and facing down. Slide stack of envelopes down until it stops.Chapter 4 20 Paper basics.5 Copy and scan.

Copy documents or photos Scan to a computer Tips for copy success Tips for scan success Copy documents or photos NOTE: All documents are copied in normal quality print mode. You cannot change the print mode quality when copying. ▲ Do one of the following: 1-sided original to 1-sided copy a. Load either small photo paper or full-size paper in the input tray. Load original. Lift lid on product. Load original print side down on right front corner of glass.Chapter 5 Close lid.

Press Fit to Page to enlarge or reduce the original. Press either Start Copy Black or Start Copy Color. Increase the number of copies by pressing the button multiple times. Scan to a computer NOTE: To scan to a computer, the HP Deskjet 2510 and computer must be connected and turned on.

▲ To scan to a computer: Single page scan a. Load original. Lift lid on product. Load original print side down on right front corner of glass.Close lid. Start the scan job by either pressing Scan on the control panel or using the Printer Software. Click the HP Deskjet 2510 series desktop icon to open the Printer Software.

NOTE: You can also access the Printer Software by clicking Start Programs HP HP Deskjet 2510 series HP Deskjet 2510 series Select Scan a Document or Photo. You will see scan options that you can select onscreen.Chapter 5.

Press Fit to Page to enlarge or reduce the original image to fit the paper size on which you are printing. Click here to go online for more information.

Tips for scan success. Load your original print side down on the right front corner of the glass. Clean the scanner glass and make sure that there are no foreign materials adhering to it. Click here to go online for more information.6 Work with cartridges. Check the estimated ink levels Order ink supplies Replace the cartridges Use single-cartridge mode Cartridge warranty information Check the estimated ink levels You can easily check the ink supply level to determine how soon you might need to replace a cartridge.

The ink supply level shows an estimate of the amount of ink remaining in the cartridges. The printer's control panel display shows the estimated ink level directly.Chapter 6 Locate the cartridge number in the Printer Software 1. Click the HP Deskjet 2510 series desktop icon to open the Printer Software. NOTE: You can also access the Printer Software by clicking Start Programs HP HP Deskjet 2510 series HP Deskjet 2510 series 2. In the Printer Software, click Shop and then click Shop For Supplies Online. The correct cartridge number will be automatically displayed when you use this link.

To order genuine HP supplies for the HP Deskjet 2510, go to www.hp.4. Insert new cartridge. Remove cartridge from packaging. Remove plastic tape using pink pull tab. Slide cartridge into slot until it clicks into place.

Close cartridge door. Align cartridges.Chapter 6 Use single-cartridge mode Use the single-cartridge mode to operate the HP Deskjet 2510 with only one print cartridge. The single-cartridge mode is initiated when a print cartridge is removed from the print cartridge carriage.

During single-cartridge mode, the product can copy documents, copy photos, and print jobs from the computer. NOTE: When the HP Deskjet 2510 operates in single-cartridge mode, a message is displayed on screen.7 Connectivity. USB Connection (non-network connection) Connect a new printer USB Connection (non-network connection) The HP Deskjet 2510 supports a rear USB 2.0 High Speed port for connection to a computer. To connect the product with the USB cable ▲ Refer to the setup instructions that came with your product for information on connecting to a computer with a USB cable. NOTE: Do not connect the USB cable to the product until you are prompted to do so.Chapter 7 30 Connectivity.8 Solve a problem This section contains the following topics:. Improve print quality Clear a paper jam Unable to print HP support Improve print quality 1. Make sure you are using genuine HP cartridges.

Check the Printer Software settings to make sure you have selected the appropriate paper type and print quality from the Media drop-down list. Check the estimated ink levels to determine if the cartridges are low on ink. For more information, see Check the estimated ink levels.Chapter 8 6. Clean the print cartridges automatically, if the diagnostic page shows steaks or missing portions of the color and black boxes.

To clean the cartridges automatically a. Load letter or A4 unused plain white paper into the input tray. In the Printer Software, click Print & Scan and then click Maintain Your Printer to access the HP Deskjet 2510 series Toolbox. Click the Device Services tab.

Click Clean Ink Cartridges. Follow the onscreen instructions.Output tray. If the paper jam is located near the front output tray, pull the paper gently out of the output tray. You may need to open the carriage door and slide the print carriage to the right to access the paper jam. Inside of printer.

If the paper jam is located inside the printer, open the cleanout door located on the bottom of the printer. Press tabs on both sides of the cleanout door. Remove jammed paper.

Hp Regulatory Model Fclsd 0508 Manual Transmission System

Close the cleanout door.Chapter 8 If the above solutions do not resolve the problem, click here for more online troubleshooting. Prevent paper jams. Do not overfill the input tray.

Remove printed papers from the output tray frequently. Ensure that paper loaded in the input tray lays flat and the edges are not bent or torn. Do not combine different paper types and paper sizes in the input tray; the entire stack of paper in the input tray must be the same size and type.c. If the wrong product is set as the default printer, right-click the correct product and select Set as Default Printer. Try using your product again. Restart the print spooler. To restart the print spooler a.

Depending upon your operating system, do one of the following: Windows 7. From the Windows Start menu, click Control Panel, System and Security, and then Administrative Tools. Double-click Services. Right-click the Print Spooler, and then click Properties.Chapter 8 Clear the print carriage Remove any objects, such as paper, that are blocking the print carriage. NOTE: Do not use any tools or other devices to remove jammed paper.

Fclsd

Always use caution when removing jammed paper from inside the product. Click here to go online for more information. Identify a defective cartridge If both the tri-color and black ink level indicators are blinking, and the Power light is on, both cartridges may still have tape on, or are missing.Resolve copy and scan issues Click here to go online for more information. HP support. Register the product Support process HP support by phone Additional warranty options Register the product By taking just a few quick minutes to register, you can enjoy quicker service, more efficient support, and product support alerts. If you did not register your printer while installing the software, you can register now at www.register.hp.com.Chapter 8. Serial number (located on the back or bottom of the product) Messages that appear when the situation occurs Answers to these questions: ◦ Has this situation happened before?

◦ Can you re-create it? ◦ Did you add any new hardware or software to your computer at about the time that this situation began? ◦ Did anything else occur prior to this situation (such as a thunderstorm, product was moved, etc.9 Technical information The technical specifications and international regulatory information for the HP Deskjet 2510 are provided in this section. For additional specifications, see the printed documentation that came with the HP Deskjet 2510.

Hp Regulatory Model Fclsd 0508 Manual Transmission

PMP Reconditioned T5 Transmissions1/15/18. TREMEC T5 PARTS UPDATETremec is no longer making some T5 parts. This is going to make us ONLY be able to build 3 types of T5s 250HP/405-500HP 295 4 diffrent ways/600HP aftermarket gear kit. Let PMP Repair yours $275.00Labor + Parts/ ShippingPrices are base on core exchange so $300.00 will be added, Until we recieve an ACCEPTABLE core. MUSTANGS 1983-2010.Early T5 Mix 83-93. $799.00300HP.Stock T5 83-93. $899.00250HP.Cobra T5 83-93.

Hp Regulatory Model Fclsd 0508 Manual Transmission Test

NO LONGER AVAILABLE.V6 3.8 T5 Mech. $869.00250HP.V6 3.8 T5 Ele.370HP NO LONGER AVAILABLE.Stock T5 94/95. $949.00250HP.Cobra T5 94/95.370HP NO LONGER AVAILABLE.94/95 T5 CRYO/HD KEYS.430HP NO LONGER AVAILABLE.V6 2005-2010 Hydraulic. $899.00320HP.295SHD T5 83-93. $1,529.00420HP + Solid3/4 keys $90.00 PMP Part#:070.

this unit is built w/ 295 1st gear, Steel Bearing Retainer, Higher Alloy Steel, Cluster Support Plate, You can+$90.00 3/4 assembly has solid HD keys, your choice of overdrive 59/64% Add Solid 3/4 Keys.295SHD/CRYO/HD KEYS T5 83-93. $1,990.00440-500HP PMP Part#:070.this unit is built w/ 295 1st gear, Steel Bearing Retainer, Higher Alloy Steel, Cluster Support Plate, 3rd/4th/C/s are Cryo treated, 3/4 assembly has solid HD keys, your choice of overdrive 59/64% BULLET PROOF EDITION T5's FORD/GM NO Core + $300.00.PRO/GF Synchronized T5 600HP+83-93. Starting@ $2,190.00 PMP Part#:84-93PROGF T5S.PRO/GF Synchronized T5 600HP+94-95. Starting@ $2,250.00 PMP Part#:94/95 PROGF T5S Pro-Shifted T5 toShift Past 7000RPM.PRO/GF STR8 Cut Facetooth. $2,425.00 Starting@.PRO/GF Helical Cut Facetooth. $2,425.00 Starting@ NMRA LEGALBRAND NEW UNITSNo Cores Needed.

Hp Regulatory Model Fclsd 0508 Manual Transmission Diagram

NEW 295SHD T5 83-93. $1,895.00 405HP. No Core NeededNOW Offering 295SHD w/PMP upgrades Cluster Plate/HD Keys $2,08900 420HP the reason we are offering this trans is individual parts to build our Recon trans from Tremec have become hard to get and this is 1 way we can still build them. TKO500/600Let PMP Repair yours $400.00 L abor + Parts / ShippingFORD In Out 1st O/D. TCET4615 TKO500 10spl 31 327 68% $2,595.00 Add Ensure Shift. TCET5201 TKO500 26spl 31 327 68% $2,595.00 Add Ensure Shift. TCET5008 TKO600 26spl 31 287 64% $2,595.00 Add Ensure Shift.

TCET4617 TKO600 26spl 31 287 82% $2,595.00 Add Ensure ShiftASK IF YOUR OLD TRANS IS WORTH A REFUND???$159.00 Ensure Shift = the issue that some TKO's have shifting 2nd to 3rd is checked to make sure.it will NOT be an issue.HAVING ANY ISSUE WITH 2nd TO 3rd SHIFT??? DID YOU BACK UP,GO FORWARD AND THEN BE LOCKED OUT OF THE SHIFTER??GIVE US A CALL WE CAN HELP. T56 NO CORE NEEDED-$500.00 if you have a coreLet PMP Repair yours $400.00 L abor + Parts / ShippingPMP Reconditioned When Available.

Ford T56 03/04 Cobra. $1,990.00400HP. Ford PMPHD T56 266 1st 26spl IN 27 Out. $2,590.00700HP.

Ford PRO/GF T56 262/271/298-1st 26spl IN 27/31 Out. Race Ready T56. $4,100.00-$4,900.00 900-1,200HPCheck out the NEW Magnum's All Styles $3,050.00.they are the NEW replacement unit for the T56. Tuet011 297 1st gear 74/50% overdrive.clearance of front plate or fork modification need to + $175.00NOTE:If you are trying to bolt this unit up in an 2003/04 Cobra: DriveShaft needs to be shortened 1 1/4' and crossmember bolts holes needs to be open up 5/8' backNow Offering.Brand New.1100HP Capable Pro/GF Magnum ask about it $6,000.00.